If a low-voltage MCU talks to a peripheral on another voltage rail, is a “4-bit level translator” sufficient? For TXU0304QWBQARQ1, count the direction of every signal first. A suitable voltage range alone does not establish interface compatibility.
Three-out, one-back SPI connection checklist
This example puts the controller on Side A and one SPI peripheral on Side B. Engineering must check the actual network.
Signal | Example direction | Channel |
|---|---|---|
SCLK | Controller → peripheral | A1 → B1Y |
MOSI | Controller → peripheral | A2 → B2Y |
Chip select | Controller → peripheral | A3 → B3Y |
MISO | Peripheral → controller | B4 → A4Y |
This is an example channel allocation, not PCB pin numbering or a final schematic. Confirm voltage domains, OE and pin numbers against the package drawing.
How are the channels arranged?
TI’s TXU0304-Q1 datasheet describes a dual-supply, fixed-direction 4-bit translator. Inputs A1/A2/A3 feed three B-side outputs, while B4 feeds A4Y: three A-to-B channels and one B-to-A channel. Each supply rail supports 1.1–5.5V; check timing and electrical conditions for the actual supply combination.
“Fixed direction” matters. Software cannot freely reverse an arbitrary channel, and the device should not be treated as a general-purpose part that automatically detects direction on every line.
Check it against a simple SPI example
With an MCU on Side A and a simple SPI peripheral on Side B, SCLK, MOSI and chip select usually travel from the MCU to the peripheral; MISO returns to the MCU. This three-out, one-back arrangement is a candidate for evaluation, subject to the actual controller, peripheral and wiring.
It is not a blanket guarantee for every SPI configuration. Multiple chip selects, extra interrupts, shared data lines or a different controller arrangement require a new signal list, channel count and disabled-state review. An added signal may require another device rather than connection to a channel with the wrong direction.
Why is it not an automatic I2C-translator replacement?
Interface selection includes drive type and direction requirements as well as voltage. For example, I2C data must travel in both directions; treating a fixed-direction device as a complete two-wire I2C translation solution misses that bus behavior. Have engineering evaluate proposed substitutions against the manufacturer documentation and the full circuit, rather than approving them because both parts are called level translators.
Review both supplies and OE together
Before the RFQ, record Side A voltage, Side B voltage, the OE control source and possible power-up sequences. Engineering should check startup, disabled operation and loss of either supply against the connected devices’ requirements. One correct high-level measurement after both rails stabilize does not complete validation.
Data rate also depends on configuration. Supply voltage, loading, routing and timing requirements affect usable speed. Evaluate the intended setup rather than applying a headline maximum to arbitrary wiring.
A signal sheet procurement and engineering can share
Signal name, source, receiver and logic voltage for every line.
Assigned translator pin and whether the signal ever needs to reverse direction.
Target clock or data rate, routing and load conditions.
OE connection, disabled-state and power-transition requirements.
Approved PCB, firmware and BOM revisions.
This sheet supports accurate sourcing and meaningful substitution review. Mark missing information as unconfirmed rather than ordering a similar-looking code.
Full ordering code and technical product information
Keep TXU0304QWBQARQ1 in the BOM and purchase order. Review its package drawing against the PCB footprint rather than specifying only TXU0304 or QFN. Confirm supplied packaging quantity, partial-reel conditions, lots and shipment documentation in the quotation.
For detailed product information, read the TI TXU0304-Q1 manufacturer datasheet. To source this exact code, use the WOMAiELEC inquiry page with quantity, destination, required date and packaging needs. Availability and price require confirmation; this article is not an in-stock commitment.
Sources reviewed November 14, 2026. Validate signal integrity and startup behavior in the actual system before approving production purchasing.
Related selection guide
STM32F405RGT6 Buying Guide: Check Pins and Memory Before CPU Speed
