If a circuit needs 3.3V and less than 1A, is any “3.3V, 1A” LDO suitable? Before buying TPS74633PQWDRVRQ1, have engineering review input voltage, power loss, PCB cooling and startup conditions together. Rated output current does not guarantee continuous delivery under every operating condition.
Two different operating checks for the same LDO
Assumed input/output/load | First calculation | Next check |
|---|---|---|
5V → 3.3V, 0.5A | Approximate loss: 0.85W | Actual PCB heat path and maximum ambient temperature |
3.6V → 3.3V, 1A | Nominal headroom: 0.3V | Input tolerance, wiring loss and worst-case dropout |
Both rows are hypothetical examples. Nominal headroom does not establish worst-case suitability; rated current alone does not demonstrate sustained operation without thermal evidence.
Specify the full code, not just TPS746
TI’s TPS746-Q1 datasheet describes a 1A LDO family with power-good output and a 1.5–6.0V input range. TPS74633PQWDRVRQ1 is the fixed 3.3V option in the 6-pin DRV WSON package. A different output or package is a different ordering code requiring review.
The 1.5V minimum family input does not mean that this 3.3V version can boost 1.5V to 3.3V. An LDO needs input above the desired output with sufficient headroom for the load and temperature conditions. It does not replace a boost converter.
A power-loss example buyers can understand
The following is an assumed operating condition, not a measurement. With 5V input, 3.3V output and 0.5A load, neglecting quiescent current gives approximate LDO loss of (5 − 3.3) × 0.5 = 0.85W. At 1A, that term becomes about 1.7W.
This calculation flags a need for thermal assessment; it does not independently prove that the device will overheat or operate safely. Temperature rise depends on PCB copper, soldering, ambient temperature and heat paths. Evaluate the correct package on the actual board and confirm with measurements.
Why does low dropout not remove the thermal question?
Dropout describes the input-output headroom needed to maintain regulation. Dissipation depends on the actual voltage difference and load. A low-dropout regulator can still generate substantial heat when input is well above output.
Request three engineering conclusions: regulation at minimum input, thermal suitability at maximum input and load, and acceptable startup and load-step behavior. A room-temperature no-load test leaves important operating conditions unverified.
Output capacitors and PG also affect the BOM
Do not select the output capacitor from its printed capacitance alone. Engineering should check effective capacitance at the actual voltage and temperature, plus layout, against the manufacturer’s stability requirements. Keep substitutions within approved specifications.
PG provides output-voltage status to the system. If reset or sequencing relies on it, review the selected variant’s output type, connection and timing rather than assuming identical behavior across every TPS746-Q1 code. Observe output voltage, EN and PG together during sample testing.
Why keep DRB and DRV package suffixes?
The family offers different packages. A quotation shortened to “TPS74633” omits information needed for footprint, pin-count and assembly checks. Match the complete ordering code and manufacturer package drawing to the approved BOM before agreeing on packaging, quantity and delivery.
If a supplier proposes another fixed-output or adjustable version, “it can also produce 3.3V” is insufficient for approval. Feedback components, pins and startup behavior may require reassessment. Engineering approval should precede a volume order.
Sample and production purchasing checklist
Specify TPS74633PQWDRVRQ1, sample and production quantities, and destination.
Have engineering record input range, continuous and peak loads, PCB revision and ambient conditions.
Validate startup, load changes, ripple and temperature rise with recorded methods and acceptance limits.
Confirm packaging, lots, labels and agreed shipment documents.
Obtain written confirmation of available quantity, quote validity, shipment and estimated arrival dates.
Detailed information and sourcing inquiry
Read the TI TPS746-Q1 product details and manufacturer datasheet. For this exact ordering code, send requirements through the WOMAiELEC inquiry page. Organize associated parts on the BOM page.
Sources reviewed November 14, 2026. Availability, price and lead time require confirmation. The calculation example does not replace thermal design and sample validation.
Related selection guide
UCC27517ADBVR Buying Guide: What Does a 4A Gate Driver Really Mean?
